Hola de nuevo,
Volviendo sobre el tema no busco discusión, sino solamente aclarar algo que para mí no está tan claro.
Para empezar según la publicación, se habla de temple o endurecido de manera ambigua. E igualmente para el revenido / temple.
En unos casos temple = endurecimiento, en otros temple=revenido
Entiendo que en nuestro caso temple = endurecimiento.
Para el texto de abajo, endurecimiento = hardening. Siento que este en inglés
Aleaciones de acero inoxidable
- martensíticos (serie AISI 400*)
- ferríticos (serie AISI 400*)
- austeníticos (serie AISI 300*)
- endurecibles por precipitación
- duplex
Families of stainless steels
There are several families of stainless steel: FERRITIC, MARTENSITIC, AUSTENITIC and DUPLEX. These names are derived from the crystal structure of the steels, which governs their metallurgical behaviour.
FERRITIC stainless steels are magnetic, have a low carbon content and contain chromium as the main alloying element, typically between 13% and 17%.
They are not hardenable by heat treatment.
MARTENSITIC stainless steels are magnetic, containing typically 12% chromium with a higher carbon content than the ferritic types.
They are hardenable by quenching and tempering like plain carbon steels and find their main application in cutlery, aerospace and general engineering.
AUSTENITIC stainless steels are non-magnetic and, in addition to chromium typically around 18%, contain nickel. This enhances their corrosion resistance and modifies the structure from ferritic to austenitic. They are the most widely used group of stainless steels.
They are not hardenable by heat treatment. DUPLEX stainless steels are used where combinations of higher strength and corrosion resistance are needed. They have a mixed structure of austenite and ferrite, hence the term "duplex". They are not hardenable by heat treatment.
PRECIPITATION HARDENING stainless steels, like the martensitic types,
can be strengthened (i.e.hardened) by heat treatment. The mechanism is metallurgically different from the process in the martensitic types. This means that either martensitic or austenitic precipitation hardening structures canbe produced.
"Super" austenitic or "super" duplex grades have enhance pitting and crevice corrosion resistance compared with the ordinary austenitic or duplex types. This is due the further additions of chromium, molybdenum and nitrogen to these grades.
En mi caso tengo varillas omer y demka.
Las de omer creo que son 17-4PH, acero martensítico endurecible por precipitación. La máxima dureza la alcanza al ser enfriado al aire tras un calentamiento aprox a 450íƒÆ’í¢â‚¬Å¡íƒâ€š.- C. Realizando un afilado suave (a mí nunca se me pone al rojo) y dejándolo enfriar al aire entiendo que obtengo la máxima dureza 46 HRC. Mas o menos, nada es perfecto.
En el caso de las demka, creo que es acero 301. A pesar de que en el texto de arriba dice claramente que los austeníticos no pueden endurecerse por tto térmico. He leído sin embargo que este acero puede endurecerse calentándolo hasta 1010-1150 íƒÆ’í¢â‚¬Å¡íƒâ€š.-C y enfriándolo luego en agua. Siendo perfectamente válido el enfriamiento al aire para piezas estrechas. Caso que nos ocupa.
Resumiendo para caso demka. No creo que la varilla se caliente por encima de 1000 íƒÆ’í¢â‚¬Å¡íƒâ€š.-C (color cereza oscuro), al menos en mi caso. Aún así valdría enfriamiento al aire.
Esto es solo un caso particular, para dos varillas. Y todo depende por supuesto de la TíƒÆ’í¢â‚¬Å¡íƒâ€ší‚ª alcanzada al afilar. Otros aceros no se que les correspondería.
De verdad que me encantaría aclarar este tema al máximo, puesto que puedo estar equivocado. En cualquier caso el tema de los aceros es como todo un mundo muy complejo, y no valen las generalidades.
gracias por compartir vuestras experiencias
: